View all »

Browse by brand

- click logo for brand listings
  • A3

Weaver RBD100 Inflatable Boat Snap Davit Set

For storing the inflatable on the swim platform (duckboard).
Weaver RBD100 Inflatable Boat Snap Davit Setclick for larger image
back to listings
NZ $629.00Product #57769

For storing the inflatable on the swim platform (duckboard).

NB: The black pads broke down in UV light so they have been replaced with gray pads which are UV resistant

Snap Davits for soft or hard bottomed Inflatable dinghies for yachts with Swim Platforms with Black Pads.

Requires glue, sold seperately.

Weaver Industries highly recommends having a knowledgeable person in inflatable boat repair to glue the pads on for you.
Do not try to glue items onto your dinghy in the rain, on the
dock or in very high humidity. Glue and water don't mix.

Step 1 - Determine where to locate the davit heads on the swim
platform, beware of support brackets underneath.
Step 2 - Mark the inflatable where the davit heads will line up
with the mounting pad on the dinghy. See figure #1. The pads
should be placed as far apart on the dinghy as possible. The
bottom of the pad goes at the top of the rub strip. The dinghy is
Step 3 - The inflatable must be wiped down with the proper
cleaner prior to gluing on the rubber pads. Match the cleaner to
the type of glue you will be using. Incompatible glue and cleaner
will cause the pad to loosen.
Step 4 - Inflatables made from hypalon require a good two-part hypalon glue such as Weaver 2001, Bostick 2402 or Apollo 2990 for proper gluing and Acetone, MEK or Toluene as a cleaner. Boats made
from a PVC derivative such as the Zodiac will require special urethane glue such as Weaver 3001 or
Apollo 3026 and MEK or Acetone cleaner.
CAUTION: Do not glue the pads on in the sun, by the water, or in high humidity. Do not sand or grind the surface of a PVC boat.

Step 5 - (ONLY FOR HYPALON BOATS) Once you have the proper glue you will need to sand the surface of the inflatable where the pads are to be glued. You can do this by using a sandpaper floppy disc you attach to a drill motor or by hand with 60 grit paper. Be very careful not to damage boat.
The surface of the inflatable should now be cleaned with the proper cleaner to remove any trace of finger oils or dust. See figures #2, 3, and 4.
Step 6 - The pads have been ground at the factory and primed with one layer of glue, but be sure and recheck the surface before installing. See figure #5. Wipe down the pads to make sure both are clean! Your goal is to clean all finger oils from surface.
Step 7 - The next step is to cut the bristles short on a paint brush and stir the can of glue to get a good mixture. Mix up your glue with proper ratio of glue to catalysis. The small bottle of catalysis is
proportioned to mix into the whole can of glue. Smaller amounts can be mixed according to directions.

Step 8 - Paint both the pad and the area of the inflatable where the pad will be installed with a thin coating of glue.
Step 9 - Let the glue set until the surface is no longer tacky to the touch (about 10-15 minutes, keep checking). Next spread a second thin layer of glue on both pieces and let set again until the surface is tacky to the touch.

(FOR PVC BOATS ONLY!) Use a hair dryer to warm the surface of the glue on the pad and dinghy. Once warm (not hot) to touch stick pad to dinghy and follow Step 10.

Step 10 - Attach the pad to the inflatable, see figure #8, and rub the air out from under the pad using a hard roller or rounded stick. You may want to deflate the boat to assure a better bond for the pad. It is critical to get all the air out from between the pad and the inflatable and the pad is sealed around the edges.
Step 11 - Once the air is out from under the pad, let the pad set-up for 48 hours. **DO NOT TOUCH IT!!** After 48 hours attach the stainless steel yoke with the 3/4" long hex head bolts. A little grease on the bolt will keep the threads from gauling. The glue will be 100% set in 7 days.
Step 12 - The same procedure is used to install the Stand-off pad. See figure #11.
Step 13 - The next step is to install the davit heads on the back of the yacht. First hold the davit head on the spot that lines up with the rubber pad on the inflatable. **Note: tie a string to the heads, so
you don't have to get a diver to retrieve one.**
Step 14 - Mark and drill the holes. Insert the 2" long bolts provided (or longer ones as necessary) through the holes and secure the davit head from under the swim platform with the nuts provided. It is
important at this point that you attach the mounted davit head to your inflatable pad.
Step 15 - Next, hook the remaining davit head to the dinghy and mark where the holes will be drilled in the swim platform. Drill the holes for the second davit head and insert the bolts and tighten nuts
provided. On integrated swim platforms you may have to follow a different procedure for installation. Call your dealer or Weaver Industries to find out how to install on an integrated swim platform.
Step 16 - You are now ready to pivot the dinghy to a vertical position to secure it to you boat. It is recommended that The Original Weaver Stand-Off Brackets be installed. This simple method consists
of a set of rubber pads which are glued in a similar manner as the davit pads to the inflatable. The Stand-Off Brackets are than installed on the back of the yacht and are used for attaching to the clips on the inflatable.
Step 17 - The swivel end of the Stand-Off Bracket is attached to the transom of the yacht. An extra set of clips are provided for attaching the Stand-Off Bracket back to the transom when not in use.


Shipping: Smart Marine uses Courier Post and Toll to deliver our NZ orders. All parcels are insured plus you will receive online trace details for peace of mind. Due to insurance and guarantee of delivery, all our parcels will need to be signed for or the courier will leave a card to collect/arrange another delivery time so please consider supplying a business address instead or another where the parcel can be signed for. Orders are processed on week days and are usually collected the next business morning by the courier, if not earlier. North Island delivery is usually 1-3 days, South Island 2-5 and the parcel size can effect this. We also ship to rural addresses and to P.O. boxes but very large/fragile/DG parcels will need a physical address.

Collect Your Order at any Smart Marine Store: Smart Marine happily allows collection of your order (pre-pay online or pay in store), 8am-6pm, 7 days a week via your favourite Smart Marine store: Westhaven, Mt Wellington, Manukau or Hamilton. Simply 'Add to Cart' as normal and select the store you want to collect from via the drop-down options at check-out. The Smart Web Crew will be in touch with when it is ready for you. Easy-peasy! Please let us know when you hope to collect so we can do our best to have it ready for you in good time. You will be required to present your own photo i.d. for pre-paid orders so please bring this with you.

Please click here to view full shipping terms and International Shipping details of required.

**Please Note: ships overseas web orders outside of New Zealand to these countries only: Cook Islands, Fiji, French Polynesia, New Caledonia, Niue, Samoa, Tahiti, Tonga, Vanuatu, Wallis & Fortuna.

Satisfaction Assured! Money Back Gaurantee!

We believe you will be very satisfied with your purchase from Smart Marine.

You are however welcome to return the item if required for exchange or refund excluding shipping costs within 10 days and in its original condition and packaging if you no longer require the item.

On the rare occasion that a product is found to be faulty under warranty or not as described, please contact the Smart Crew and we will promptly remedy the issue for you. If you have any queries regarding items on the SmartWeb or concerns with your purchase, please feel free to contact the Smart Crew for help.

Smart Marine aims to abide and exceed the requirements set by the New Zealand Fair Trading and Consumer Guarantees Act to ensure you have a Smart Shopping Experience!