Inter Perfection Plus Polyurethane Gloss Varnish (2-Pk) 750Ml

High performance two pack extrerior polyurethane varnish.

The ultimate product for durability, gloss retention and UV resistance with a very long life.

Product Description:

Perfection Varnish is the ultimate in varnish performance combining excellent chemical and abrasion resistance with superb gloss. It is the premium two pack high performance clear varnish, for beautiful wood with a tough finish.

* Chemical cure gives resistance to fuels, oil and mild acids and alkalis
* Longer service life than ordinary varnishes
UV filters combine with the chemical cure to give the longest possible life.

Application Details - Perfection Varnish :
Finish/Sheen- Full gloss

Colour:  Clear
Converter/Curing -YVA850
Thinner: YTA006
Number of Coats: 4 coats minimum
Method of application: Brush / Roller / Conventional Spray
Suitable for high speed craft? NO

Specific Gravity 1.04
Volume Solids 43%
Mix Ratio 3:1 by volume
Typical Shelf Life- 2 yrs
VOC (As Supplied)- 530 g/lt

Drying: Touch Dry/Potlife:

5ºC: 7hrs/5hrs

15ºC: 5hrs/3hrs

23ºC: 2hrs/2hrs

35ºC: 1hrs/1hrs

Overcoating Substrate Temperature -Overcoated by Perfection Varnish: Min/Max

5ºC: 28hrs/4days 

15ºC: 14hrs/3days

23ºC: 6hrs/2days

35ºC: 4hrs/1days

Note:If Maximum Recoat Times are exceeded, sand using 280-400 grade (grit) wet or dry paper.

APPLICATION AND USE:

Preparation BARE WOOD:

Sand smooth with suitable grades of paper finishing with typically 280-320 grade paper. On oily timbers degrease thoroughly and apply Epiglass Everdure as a sealer prior to applying Perfection Varnish.

PREVIOUSLY VARNISHED WOOD:
In Good Condition: Wash down with fresh water to remove salt deposits. Remove any oil, grease or similar contamination using Surface-Prep. Sand smooth with 280-320 grade paper. Remove sanding residue.
In Poor Condition: Remove all previous coatings. Follow directions for bare wood.
Priming bare wood: Apply 1 coat of Perfection Varnish thinned 10-15% with YTA006 International Retarder Thinners #9 or YTA064 International Polyurethane Spraying Thinners #10 to ensure penetration and adhesion.

Method: For best results when applying by roller, smooth off with a pad or brush.

Hints:

Mixing-Stir individual products prior to mixing. Mix the amount you expect to use in a separate container. Add Curing Agent to the Base, stir and leave for 10 minutes to allow bubbles to disperse.
Thinner- YTA006 International Retarder Thinners #9. (When brushing). YTA064 International Polyurethane Spraying Thinners #10. (When spraying).
Cleaner- YTA006 International Retarder Thinners #9.
Ventilation and Humidity Control- Apply in dry, well ventilated conditions. Best applied at ambient temperatures of between 15°C and 20°C. Sensitive to moisture during application. Avoid excessively humid conditions, over 80% relative humidity. Avoid applying late in the evening as condensation can cause a loss of gloss overnight.

Some Important Points: Avoid painting in direct sunlight. Do not use unless mixed thoroughly with the curing agent at specified ratio. Contains Isocyanates which may be harmful to lungs, read the safety data section before use. Not suitable for continuous immersion. Product temperature should be minimum 15°C/59°F and maximum 35°C/95°F. Substrate temperature should be minimum 5°C/40°F and maximum 35°C/95°F.

Compatibility/Substrates: Not compatible with Teak, Iroko and other oily wood types. Will crack on carvel and clinker/lapstrake hulls. Do not use Perfection Varnish on flexible constructions. It should not be used over any one pack products.

Number of Coats- 4 coats minimum

Coverage (Theoretical) - 12.20 (m²/lt)

(Practical) - 11.00 (m²/lt)

Recommended DFT- 35 microns dry by brush

Recommended WFT- 82 microns wet by brush

Application Methods- Brush, Roller, Conventional Spray

Visit the International Yacht Paints website via this link for more painting & product advice.